Problems
Troubleshooting
Wireless audio usually works unnoticed until it lets you down at the worst possible moment. The good news is that most glitches have nothing to do with a fault: the headphones connected to the wrong device, walls or nearby signals are getting in the way, or a sound setting has been changed. Below are common situations and a sequence of steps that helps in most cases.
Before doing a reset, check the simplest things: the charge, the distance and whether the headphones are connected to another device.
How this section works: situations are described in general terms. If your headphones get hot, swell or smell of burning, don't try to fix them: stop using them and contact the manufacturer.
Common situations
The headphones don't appear in the device list.
Check that they are charged and actually in pairing mode, not just switched on. If a laptop or tablet they already know is nearby, the headphones may have quietly connected to it: turn off Bluetooth on that device and try again.
The sound drops out and crackles.
Bluetooth works in the 2.4 GHz band, the same one used by many home Wi-Fi routers and microwave ovens, so interference is possible. Walls and even your own body weaken the signal too, for example if the phone is in your back pocket. Bring the phone closer and take it out of a closed bag.
The sound lags behind the video.
Wireless audio always has a slight delay. Restart the video or the player: many adjust themselves to the headphones. If your headphones have a low-latency mode, turn it on, and for games consider a wired connection.
Only one earbud is playing.
Put both earbuds in the case, close the lid and wait a moment, then take them out again. Check that both are charged and that the contacts in the case are clean. Look at the balance settings too: the sound may have been shifted to one channel by accident.
People on calls can't hear me well.
Check in the call settings which microphone is selected: the phone's or the headphones'. The microphone openings should not be covered by hair or clothing or clogged with dust. In wind or a noisy crowd any headphones pick up voices less clearly, so it is better to take an important call somewhere quiet.
The headphones run out of charge quickly.
Noise cancelling and high volume use up the charge faster. A battery loses capacity over time, which is natural. Don't leave headphones completely flat for long periods or keep them somewhere hot: these conditions age a battery fastest.
If your headphones won't connect any more
Restart everything
Turn Bluetooth off and on again on your phone, and put the headphones in their case or switch the speaker off for a few seconds.
Disconnect other devices
Turn off Bluetooth on the laptop, tablet and any other devices the headphones have paired with before, so they don't grab the connection.
Forget the device
In the paired devices list, select the headphones and remove them. The phone will stop trying to connect using the old data.
Reset the headphones
Do a factory reset strictly following the manufacturer's instructions. It is usually a specific long press of a button on the headphones or the case, but methods vary a lot.
Connect again
Turn on pairing mode and connect as if for the first time. Check the sound and the microphone.
If that didn't help
Try connecting the headphones to a different phone. If that doesn't work either, contact the manufacturer's support or a repair service rather than taking the device apart yourself.
Read next
- Guides
Step-by-step advice: first connection, two devices at once, sound in videos and games, the microphone on calls, caring for ear tips. Plus our article catalogue.
- Tools
The paired devices list, pairing mode, the charging case, sound settings, the volume warning and finding a lost earbud.
- Comparisons
In-ear, on-ear and over-ear headphones, wired versus wireless, headphones versus a portable speaker: pros, cons and who each one suits.
- Security
Loud sound for long periods, headphones on the street and in transport, unwanted connections, loss, battery overheating and selling without a reset.
- Glossary
Pairing, multipoint, codec, latency, noise cancelling, transparency mode, ear tips and cushions and other terms, in plain language.
Sources
- Reference material on Bluetooth (in general terms)
- Headphone and speaker manufacturers' instructions (in general terms)
- The guide's editorial material
This guide describes wireless audio in general terms and reflects the editors' view as of the date it was prepared. Headphones and speakers are controlled in different ways: some with a button, some with a touch, and settings on phones and computers are not always named the same. If your device's manual says otherwise, follow the manual.